|
|
Enquiry
|
|
Click on image for larger photo
|
Product Code:
11154-1
AIR EXHAUST JACK 4 TON SIZE 640 X 720MM
INFLATED WITH TAILPIPE EXHAUST MATERIAL
IS 1000D DENIER 1.0MM PVC & CARRY BAG
|
|
|
|
|
Please enter a valid quantity |
|
|
|
|
 |
|
|
|
FAMOUS WEL-BILT BRAND
NOTE - LOW SPEED ENGINE WILL INFLATE THE JACK
SIZE OF AIR BAG 64 X 72CM
INFLATED WITH TAILPIPE EXHAUST
4 TONNE LOAD
NON RETURN VALVE IN MIDDLE OF EXHAUST HOSE
5 HEAVY DUTY ANTI SLIP SPIKES ON BAG
4 ANTI SLIP MATS ARE SUPPLIED FOR UNDER AIR BAG
1 PATCH REPAIR KIT IS SUPPLIED WITH 2 LARGE PATCHES - GLUE PAIR OF GLOVES
THE JACK IS CAPABLE OF LIFTING THE VEHICLE OUT OF RUTS OR HOLES, TO CHANGE A TYRE OR TO INSTALL SNOW CHAINS.
GREAT FOR USE IF YOU ARE STUCK IN SAND, MUD, SNOW OR SOFT GROUND.
SIMPLE TO USE WITHOUT THE RISK OF DAMAGE TO YOUR VEHICLE AS CAN HAPPEN WITH A HIGH LIFT JACK.
BAG WILL STAY INFLATED FOR OVER AN HOUR.
PACKS AWAY IN ITS OWN STORAGE BAG, READY FOR USE.
PRODUCT TIPS
AN ESSENTIAL PIECE OF EQUIPMENT THAT YOU SHOULD ALWAYS CARRY IN YOUR VEHICLE IN CASE OF EMERGENCY.
CAN ALSO BE USED ON TRAILERS, CARAVANS OR FARM IMPLEMENTS.
WARRANTY
6 MONTHS FROM DATE OF PURCHASE, AGAINST FAULTY MANUFACTURE AND MATERIALS
DOES NOT COVER ANY WEAR AND TEAR ASSOCIATED WITH NORMAL USE.
SAFETY PRECAUTIONS -
WARNING: FAILURE TO HEED THE FOLLOWING WARNINGS CAN RESULT IN PERSONAL INJURY AND/OR EQUIPMENT DAMAGE.THESE WARNINGS CANNOT COVER EVERY SITUATION, SO HAVE SAFETY FOREMOST IN YOUR MIND WHEN SETTING UP A JOB.
- READ, UNDERSTAND AND FOLLOW THE OPERATING INSTRUCTIONS AND THE ANSI B30.1 AND ASME PALD-1 SAFETY STANDARDS FOR JACKS. IF THE OPERATOR CANNOT READ ENGLISH, OPERATING INSTURCTIONS AND SAFETY PRECAUTIONS MUST BE READ AND DISCUSSED IN THE OPERATOR'S NATIVE LANGUAGE.
- WEAR EYE PROTECTION THAT MEETS THE REQUIREMENTS OF ANSI Z87.1 AND OSHA.
- INSPECT THE JACK BEFORE EACH USE; DO NOT USE THE JACK IF IT IS DAMAGED, ALTERED, OR IN POOR CONIDITION.
- TO PREVENT TIPPING, SET UP THE JACK ON A HARD, LEVEL SURFACE. SET VEHICLE PARKING BRAKE AND BLOCK TYRES.
- THE LOAD MUST NOT EXCEED THE RATED LIFTING CAPACITY OF THE JACK. LIFT ONLY DEAD WEIGHT.
- CENTER THE LOAD ON THE JACK SADDLE, BECAUSE OFF-CENTRE LOADS CAN DAMAGE SEALS AND CAUSE HYDRAULIC FAILURE.
- USE THE JACK FOR LIFTING PURPOSES ONLY. THIS JACK IS DESIGNED TO LIFT LOADS, NOT SUPPORT LOADS. IMMEDIATELY SUPPORT A LIFTED LOAD WITH JACK STANDS.
- STAY CLEAR OF LIFTED LOADS.
- USE ONLY APPROVED HYDRAULIC FLUID, SUCH AS CHEVRON AW HYDRAULIC OIL MV OR EQUIVALENT.
- THE JACK SHOULD BE USED ON HARD, LEVEL SURFACES
- THE WHEELS OF THE VEHICLE TO BE CHOCKED
- DO NOT PUT A PORTION OF YOUR BODY UNDER A VEHICLE SUPPORTED BY A JACK
- NO PERSON SHOULD REMAIN IN A VEHICLE THAT IS BEING JACKED
- DO NOT EXCEED THE WORKING LOAD LIMIT
OPERATING INSTRUCTIONS -
TO RAISE THE JACK, USE NARROW END OF JACK HANDLE TO TIGHTEN RELEASE VALVE CLOCKWISE (CW). INSERT HANDLE INTO SOCKET AND OPERATE PUMP. TO LOWER THE JACK, SLOWLY OPEN THE RELEASE VALVE KNOB BY TURNING IT COUNTERCLOCKWISE (CCW).
|
View Complete Range:
|
WORKSHOP TOOLS > JACKS - AIR BAG FLOOR
TOWING & RECOVERY > JACKS - AIR EXHAUST
|
|
|
Video:
|
|
|
|
|
|