|
|
Enquiry
|
|
Click on image for larger photo
|
Product Code:
44102
BOTTLE JACK 2000KG HYDRAULIC MIN LIFT
190MM MAX LIFT 368MM WITH SCREW ADJUST-
MENT - DO NOT EXCEED THE WORKING LOAD
|
|
|
|
|
Please enter a valid quantity |
|
|
|
|
 |
|
|
|
BOTTLE JACK 2000KG HYDRAULIC
APPLICATION:
BOTTLE STYLE HYDRAULIC JACK FOR THE SAFE LIFTING OF VEHICLES OR OTHER HEAVY LOADS OR EQUIPMENT SO MAINTENANCE CAN BE PERFORMED.
FEATURES:
HEAVY DUTY STEEL CONSTRUCTION WITH QUALITY CAST IRON BASE PLATE
MECHANICAL HEIGHT ADJUSTMENT SCREW
CHROME HYDRAULIC RAM AND PISTON PUMP
BLACK BAKED ENAMEL FINISH FOR CORROSION RESISTANCE
AUSTRALIAN STANDARD COMPLIANCE
SPECIFICATIONS:
WORKING LOAD LIMIT: 2000KG
MINIMUM HEIGHT: 190MM
MAXIMUM HEIGHT: 368MM
HYDRAULIC LIFT HEIGHT: 116MM
SCREW ADJUSTMENT HEIGHT: 48MM
AUSTRALIAN STANDARD AS/NZS 2693:2007
MAINTENANCE:
IT IS RECOMMENDED THAT THE OIL LEVEL SHOULD BE AT APPROXIMATELY 3MM BELOW THE OIL FILLER HOLE. TO ADD OIL LOWER JACK TO THE LOWEST POSITION, THEN REMOVE THE AIR VENT VALVE, ADD OIL TO DESIRED LEVEL, PUMP JACK 5 OR 6 TIMES TO EXPEL ANY AIR IN THE CYLINDER, AND THEN FASTEN THE AIR VENT VALVE. AVOID MIXING DIFFERENT TYPES OF FLUIDS. USE ONLY ISO 10-5 HYDRAULIC FLUID. DO NOT USE BRAKE FLUID, ALCOHOL, GLYCERINE, DETERGENT, MOTOR OIL OR DIRTY OIL.
SAFETY NOTE:
THE JACK SHOULD BE USED ON HARD, LEVEL SURFACES
THE WHEELS OF THE VEHICLE TO BE CHOCKED
DO NOT PUT A PORTION OF YOUR BODY UNDER A VEHICLE SUPPORTED BY A JACK
NO PERSON SHOULD REMAIN IN A VEHICLE THAT IS BEING JACKED
DO NOT EXCEED THE WORKING LOAD LIMIT
SAFETY PRECAUTIONS -
WARNING: FAILURE TO HEED THE FOLLOWING WARNINGS CAN RESULT IN PERSONAL INJURY AND/OR EQUIPMENT DAMAGE.THESE WARNINGS CANNOT COVER EVERY SITUATION, SO HAVE SAFETY FOREMOST IN YOUR MIND WHEN SETTING UP A JOB.
- READ, UNDERSTAND AND FOLLOW THE OPERATING INSTRUCTIONS AND THE ANSI B30.1 AND ASME PALD-1 SAFETY STANDARDS FOR JACKS. IF THE OPERATOR CANNOT READ ENGLISH, OPERATING INSTURCTIONS AND SAFETY PRECAUTIONS MUST BE READ AND DISCUSSED IN THE OPERATOR'S NATIVE LANGUAGE.
- WEAR EYE PROTECTION THAT MEETS THE REQUIREMENTS OF ANSI Z87.1 AND OSHA.
- INSPECT THE JACK BEFORE EACH USE; DO NOT USE THE JACK IF IT IS DAMAGED, ALTERED, OR IN POOR CONIDITION.
- TO PREVENT TIPPING, SET UP THE JACK ON A HARD, LEVEL SURFACE. SET VEHICLE PARKING BRAKE AND BLOCK TYRES.
- THE LOAD MUST NOT EXCEED THE RATED LIFTING CAPACITY OF THE JACK. LIFT ONLY DEAD WEIGHT.
- CENTER THE LOAD ON THE JACK SADDLE, BECAUSE OFF-CENTRE LOADS CAN DAMAGE SEALS AND CAUSE HYDRAULIC FAILURE.
- USE THE JACK FOR LIFTING PURPOSES ONLY. THIS JACK IS DESIGNED TO LIFT LOADS, NOT SUPPORT LOADS. IMMEDIATELY SUPPORT A LIFTED LOAD WITH JACK STANDS.
- STAY CLEAR OF LIFTED LOADS.
- USE ONLY APPROVED HYDRAULIC FLUID, SUCH AS CHEVRON AW HYDRAULIC OIL MV OR EQUIVALENT.
- THE JACK SHOULD BE USED ON HARD, LEVEL SURFACES
- THE WHEELS OF THE VEHICLE TO BE CHOCKED
- DO NOT PUT A PORTION OF YOUR BODY UNDER A VEHICLE SUPPORTED BY A JACK
- NO PERSON SHOULD REMAIN IN A VEHICLE THAT IS BEING JACKED
- DO NOT EXCEED THE WORKING LOAD LIMIT
OPERATING INSTRUCTIONS -
TO RAISE THE JACK, USE NARROW END OF JACK HANDLE TO TIGHTEN RELEASE VALVE CLOCKWISE (CW). INSERT HANDLE INTO SOCKET AND OPERATE PUMP. TO LOWER THE JACK, SLOWLY OPEN THE RELEASE VALVE KNOB BY TURNING IT COUNTERCLOCKWISE (CCW).
|
View Complete Range:
|
WORKSHOP TOOLS > JACKS - BOTTLE TO 8 TONNE
|
|
|
Video:
|
|
|
|
|
|